This is a custom kit for

your Ford truck!

Buy for the future brake job!!!

This is a TrueBend 3/16 inch metal brake line

replacement kit. All lines are supplied double-flared at

each end with S.A.E. specified male inverted flare

fittings attached and are ready for quick and easy

installation. All brake lines have an extra long nut on

one end to seat in late model deep-seated wheel

cylinders. These malleable lines are easy to bend or

coil without collapsing the tubing or restricting the

flow of brake fluid. Six couplers are included to join

lines where necessary. Instructions are also included.




this kit is for the following:

Aerostar van 1986 to 1992

Bronco, U100, U150 2 & 4 WD 1978 to 1993

Bronco II 1984 to 1990

Explorer 1991 to 1993

Ranger 2 & 4 WD 1983 to 1993

E100, E150 Van 1975 to 1992

F100, F150 2 & 4 WD 1973 to 1992

E250, E350 Van 1976 to 1993

F250, F350, F450 2 and 4 WD 1973 to 1993

 

This kit will do the entire car from the proportioning

valve to the wheels. You may need adapters

to run the lines up to the master cylinder.

Here is a list of what lines are included to do the

models above

one 5 15/16 inch

two 7 7/8 inch

one 9 15/16 inch

two 11 13/16 inch

one 15 3/4 inch

three 19 15/16 inch

two 25 1/4 inch

two 29 7/8 inch

one 35 1/4 inch

two 39 7/8 inch

one 45 1/4 inch

three 50 3/4 inch

six unions to joint lines together

instructions for installation

A total of 27 lines and unions!!

 

TrueBend® brake lines resist corrosion, vibration, fatigue and shock from impact. They are coated for corrosion protection in compliance with GM132M-ASV and SAE J527B.  Each line is manufactured by double wrapping a copper coated steel strip to form a double wall tube.  Then, the tube is furnace brazed to fuse the copper/steel tube into one continuous and seamless tube.  The tube is then given a outer coat for corrosion and abrasion resistance. These lines are the strongest and safest avai; yet can still be easily bent without kinking or without damaging the  outer coat.

This kit contains all the lines to do a wide variety of trucks, and many different configurations, so you will have unused lines in any installation. These extra lines are a bonus that can be used for other projects

The tubing is double walled, seamless and copper fused with a special inner and outer coating to provide protection from abrasion and corrosion. This is the same tubing that is used on new cars!

All information on lines are for OEM brake systems only. However, this kit has many lengths and will service most modified system except any system with "larger" 1/4 (.25 inch OD) lines.  

If you need a very sharp bend next to the flare at the end of the line, you will need a bender listed under "tools/supplies" on our Ebay store.

All unions are solid brass to stop rust.

All lines are made in USA or Canada and are 3/16" outer diameter with a factory flare.

 

Fits the years: 1960 61 1961 62 1962 63 1963 64 1964 65 1965 66 1966 67 1967 68 1968 69 1969 70 1970 71 1971 72 1972 73 1973 74 1974 75 1975 76 1976 77 1977 78 1978 79 1979 80 1980 81 1981 82 1982 83 1983 84 1984 85 1985 86 1986 87 1987 88 1988 89 1989

4715